Hormann garage door opener troubleshooting

The Hörmann Group is a German manufacturer of gates, doors, frames and operators. The Group has over 10 production sites within Germany, and in addition to them, there are also manufacturing facilities in the UK, USA, India, China, Austria, Poland, France, and Netherlands. Being a family business, today Hormann is run by the grandchildren and great-grandchildren of the founder.

LED:flashes 2 x
Cause:Photocell was interrupted / not connected
Remedy: Check photocell, connect or replace as necessary.
LED:flashes 3 x
Cause:The CLOSE force limit has been activated - a safety return has taken place.
Remedy:Remove the obstruction. If a safety return has taken place for no obvious reason, check the door mechanics. It may be necessary to delete the door data and repeat the learning process.
LED:flashes 4 x
Cause:The static current circuit or wicket door contact is open or was opened during a travel cycle.
Remedy:Check the connected unit, close the electric circuit.
LED:flashes 5 x
Cause:The OPEN force limit has been activated - the door has come to a halt while opening.
Remedy:Remove the obstruction. If the door has come to a halt for no obvious reason, check the door mechanics. It may be necessary to delete the door data and repeat the learning process.
LED:flashes 6 x
Cause:Operator fault / malfunction in the operator system.
Remedy:It may be necessary to delete the door data. If the operator fault re-occurs, replace the operator.
LED:flashes 7 x
Cause:Operator has not yet performed any learning cycles (this is simply being pointed out and does not constitute an error).
Remedy:Initiate a learning cycle by pressing an external push-button, the hand transmitter button, the transparent push-button or circuit board button T (with cover removed).
LED:flashes 8 x
Cause:Operator needs to perform an opening reference cycle.
Remedy:Initiate an opening reference cycle by pressing an external push-button, the hand transmitter button, the transparent push- button or the T-button (with cover removed). This is the normal state following a power failure, if no door data is present or has been deleted and/or the last door position is not sufficiently well known.

Hormann Rollmatic garage door opener troubleshooting

DisplayError/warningPossible causeRemedy
Safety equipmentPhotocell was interrupted, is not connected.- Check photocell, replace or connect as necessary
Power limit in Close directionObstacle in door area.- Remove the obstacle.
- Delete any door data and teach in again
Static current circuitThe static current circuit (RSK) is open.- Check the connected units, close the circuit
Power limit in OPEN directionObstacle in door area.- Remove the obstacle.
- Delete any door data and teach in again
Operator errorMalfunction in operator system- Delete door data, replace operator if this recurs several times
Operator error Message, no faultThe operator has not been taught in yet.- Teach in the operator
No reference point Power failure, mechanical lockingThe operator requires an Open reference run.- Reference run in the Open direction
Emergency battery voltageVoltage of emergency battery is too low.- Further electrical operation is possible only after the mains voltage has been restored
Connecting cablesConnection to the motor connection circuit board in the operator is defective.- Check the connection and connection cables.
- Exchange the motor connection circuit board.
admin

Recent Posts

How to Adjust Garage Door Limit Switches

If your garage door does not close completely or closes and then starts to move…

5 years ago

How to Adjust Extension Springs

You will need the following tools for this work: a ladder, two C-clamps or locking…

5 years ago

How to Fix Garage Door Opener Sensors

If your garage door refuses to move in the down direction, it may be caused…

5 years ago

How to Adjust Garage Door Track by Yourself

There is a garage door track on each side of the doorway. These tracks run…

5 years ago

How to Adjust a Garage Door by Yourself

Is trying to adjust the garage door on your own worth the effort? It depends…

5 years ago

How to Adjust Garage Door Limit Switches

If your garage door does not close completely or closes and then starts to move…

5 years ago